Select Page

Formatinio pjovimo staklės

UNICA 500

Standards

The machines are equipped with:

  • 2 axes scoring unit with motorized adjustment on-off and display of the operation on the table with led
  • Aluminium carriage sliding on high precision round steel bar
  • Sliding table locking in all positions
  • Anodized carriage and profiles
  • Aluminium fence +30°-45°
  • Increased extensible fence on cross-cut carriage with lever locking of the flip over stops and read-out with LED
  • Rip fence with micrometric adjustment
  • Blade speed change from the table
  • Positioning of the fence of the cross-cut carriage with compensation of the height in relation to the tilting angle
  • Quick selection of 5 fixed positions of the flip over stop on the cross cut fence
  • Motorized lifting of the blade unit through linear actuator
  • Motorized tilting of the blade unit through linear actuator
  • Blade lifting unit sliding on 4 selflubricating linear precision guides
  • Blade unit with double separate suction for main and scoring blade
  • Suction hood on the guard “CE” dia. 80 mm
  • Suction hood on the guard “EXP” dia. 60 mm
  • Suction hood on the adjustable support dia. 120 mm

 

MACHINE “CE”
– “CE” standards with selfbraking motor 10″
– Display of the rotation speed
– Parallelogram blade guard “CE”
– Table extension
MACHINE “EXP”
– Electric equipment (overload motor porotection, emergency switch, transformer)
– Blade safety guard on the riving knife

Technical Data

Sliding table sizes 2150 385×2150 mm
Sliding table sizes 2600 385×2600 mm
Sliding table sizes 3200 385×3200 mm
Sliding table sizes 3800 385×3800 mm
Sliding table sizes 4300 385×4300 mm
Cross-cut capacity sliding table 2150 2170 mm
Cross-cut capacity sliding table 2600 2700 mm
Cross-cut capacity sliding table 3200 3260 mm
Cross-cut capacity sliding table 3800 3870 mm
Cross-cut capacity sliding table 4300 4370 mm
Cut height blade dia. 450mm 90° 154 mm
Cut height blade dia. 450mm 45° 105 mm
Cut height blade dia. 550mm 90° 200 mm
Cut height blade dia. 550mm 45° 138 mm
Blade tilt UNICA 500E 0-46 °
Blade tilt UNICA 500 DIGIT 2-DIGIT 3-PROGRAM +1-46 °
Cut width between blade and rip fence UNICA 500 E-DIGIT 2 1250 mm
Cut width between blade and rip fence UNICA 500 DIGIT 3-PROGRAM 1600 mm
Main blade dia. 450 mm
Protruding from the table with blade 450 mm completely down at 50 mm
Main blade dia. (on request on “CE”) (to use with scoring unit excluded) 550 mm
Protruding from the table with blade 550 mm (Blade lifting disconnected through electronic sensor) 50 mm
4 rotation speeds 2200-3000-4000-5000 g/1′
Scoring blade dia. 125 mm
Motor power 7,5 (5,5) hp (kw)
Scoring unit motor power 1 (0,75) hp (kw)
Noise level 88-90 db (A)
Net weight UNICA 500 E 900 kg
Net weight UNICA 500 DIGIT 1050 kg
Net weight UNICA 500 PROGRAM 1240 kg

Optional

PROVISION FOR BLADE DIA. 550 MM (Only for machine “CE”)
Complete with system to exclude automatically the scoring unit with blade fitted, which allows to install the blade with dia. 550mm without taking off the scoring blade
– Cut height with blade at 90° – 200 mm
– Cut height with blade at 45° – 138 mm
– Blade protruding from the working table 200mm (Blade lifting disconnected through electronic sensor)
NB: in case blades with dia. 450mm or lower get installed, blade lifting gets reactivated by moving the support of the riving knife
ADJUSTABLE DOUBLE SCORING BLADE
* Scoring unit with double blade – opening adjustment of the 2 blades with 0,05 mm increase (without use of keys
* Adjustment area of the blade from min thickness 2,8 mm to max thickness 3,6 mm
* Complete with double blade
REDUCTION FOR SLIDING TABLE 2150 MM (Cross-cut capacity with scoring unit 2170 mm.)
REDUCTION FOR SLIDING TABLE 2600 MM (Cross-cut capacity with scoring unit 2700 mm.)
SLIDING TABLE LENGTH 3800 MM (Cross-cut capacity with scoring unit 3870 mm.)
SLIDING TABLE LENGTH 4300 MM (Fixed cross-cut carriage capacity w/scoring unit 4300 mm)
(Tilting cross-cut carriage capacity w/scoring unit 3860 mm)
DIRECT START ON THE SLIDING TABLE
QUICK LOCKING OF THE SAW BLADE (for blade with max dia. 450mm)
QUICK LOCKING OF THE SCORING BLADE
DOUBLE FENCE FOR +45°-45° ANGULAR CUTS
DISPLAYED DOUBLE FENCE ANG.CUTS +45°-45°
SCREW AND ECCENTRIC WOODPRESSER
PNEUMATIC CLAMP WITH DOUBLE CONTROL Complete with penumatic plant to operate both from the clamp and from the sliding carriage
2ND PNEUMATIC CLAMP (Compulsory: pneumatic clamp with double control)
PNEUMATIC PRESSER 3200 MM – Panel useful length: 3050 mm.
SMALL TABLE FOR PARALLEL CUTS
SMALL TABLE PAR.CUTS/ELECTRONIC DISPLAY
INVERTER FOR SPEED FROM 2000 TO 6000 RPM VOLT 400 -(MAX 10HP)
INVERTER FOR SPEED FROM 2000 TO 6000 RPM VOLT 230 -(MAX 10HP)
‘CE’ PARALLELOGRAM BLADE GUARD (machine “EXP”)
-47°+47°DISPL.TILT CR.CUT CARRIAGE
DISPLAYED TILTING CROSS CUT CARRIAGE -47°+47° complete with:
– Digital display of cross cut carriage tilt
– No. 1 read-out for the 1st and 2nd flip over stop with separate positioning and compensation of the size in relation to the tilting angle
– Telescopic extension 470 mm
2ND ELECTRONIC READ-OUT/FENCE EXTENSION (only for model with tilting cross-cut carriage -47°+47°)
2nd electronic read-out on the extension of the cross-cut carriage fence with compensation of the size in relation to the tilting angle
2 ELECTRONIC READ-OUTS/EXTEN.FENCE (only for model with fixed cross-cut carriage)
Extensible aluminium fence for cross-cut carriage, with no. 2 electronic read-outs on the magnetic band, for flip over stops positioning:
* 1st read-out for 1st and 2nd flip over stop with separate positioning and compensation of the size in relation to the tilting angle
* 2nd read-out on the extension of the fence with compensation of the size in relation to the tilting angle
SECTOR FLIP OVER STOP to cut material with thickness lower than 2 mm
NEBULIZER TO COOL THE BLADE (Compulsory to cut aluminium)
TELESCOPIC EXTENSION MAX 750 MM OF THE CROSS-CUT CARRIAGE
2ND CROSS-CUT CARRIAGE
LASER UNIT TO OPTIMIZE CUT
TABLE EXTENSION (machine “EXP”)
KIT TO WORK WITH CUTTER (DADO BLADE) cutter size 15×200 mm
DOUBLE CARBIDE SCORING SAW BLADE D.125MM
Z 12+12 – tooth thickness 3,1/3,9 mm
CARBIDE BLADE FOR SCORING ‘CD’ DIA. 125MM
Z. 12+12 – tooth thickness 2,8/3,6 mm
DOUBLE CARBIDE SCORING SAW BLADE/3 AXES
Z 12+12 – tooth thickness 2,8/3,8 mm
CARBIDE SAW BLADE DIA. 300 MM
Z 72 – tooth thickness 3,2 mm
CARBIDE SAW BLADE DIA. 350 MM
Z 84 – tooth thickness 3,5 mm
CARBIDE SAW BLADE DIA. 400 MM
Z 60 – tooth thickness 3,8 mm
CARBIDE SAW BLADE DIA. 450 MM
Z 66 – tooth thickness 4,2 mm
CARBIDE SAW BLADE DIA. 550 MM
Z 48 – tooth thickness 5,2 mm
MOTOR POWER 10 HP (7,5 KW) 50 HZ with automatic star-delta start
MOTOR POWER 12 HP (9 KW) 60 HZ with automatic star-delta start
MOTOR POWER 15 HP (11 KW) 50 HZ with automatic star-delta start
MOTOR POWER 18 HP (13 KW) 60 HZ with automatic star-delta start

UNICA 500E

UNICA 500 DIGIT